Showing posts with label 991 transaxle. Show all posts
Showing posts with label 991 transaxle. Show all posts

Sunday, March 15, 2015

Diffuser

<<   Mount Half Shafts                                                  >>

Major System Category: Body (Undercarriage)
Task: Diffuser
Parts:
Vent Louvers
Strakes
Diffuser Grille
Diffuser
Prerequisite Tasks:
Additional Costs: $250 (estimate)
Time Requirement: 8+ hours
Date Started: February 20, 2015
Date Completed: February 28, 2015
The diffuser is the unwieldy carbon fiber piece that fits under the transaxle and extends slightly past the lip of the rear end. Factory Five supllies these little posts (ugly as sin) to connect the top of the Diffuser to the bottom of the rear frame (just below the license plate and the exhaust pipe openings). Each is entitled to their opinions, but these little post that hold the diffuser in place look cheap.
The Diffuser grille comes flat. The tabs need to be bent to provide attachment points for the grill to the body shell. These are no 90 degree angles. In order for the grille to fit properly, the angle is more acute (i.e. less than 90). With all the pieces already in the area (e.g. transaxle bracket, chassis mount for wing, backup camera, lights) there isn't a lot of room to get a rivet tool in there. I went with  short bolts and locking nuts.
Fortunately, Vraptor Speedworks makes this marvelous looking diffuser grille. I think this is a necessary purchase (from an aesthetics perspective) that really makes the back end look finished. The shape of the Gen I and Gen II cars is different, so this grille only works for the Gen II cars. I have decided to bolt the diffuser grille and diffuser to the car. The manual says to rivet everything in place. I prefer to have a way to access everything on the car without having to drill out 40 rivets.
I painted the diffuser grille gloss black, bent the tabs using a small vice as my metal bending tool. This is the grille clamped in place for initial fitment. I discovered that I had to "bow" it a little to get to go flush on the edges. The oither issue I have with rivets has to do with maintenance access. If you go the rivet route, then the only way you will ever get it off the car is to drill everything out.
Before I could pre fit the diffuser, I had to get the  half shafts and the transaxle installed. This way, I could remove the jack stands from  under the rear chassis and have free access under the car for the diffuser.The manual indicated that you should measure 1.5 inches from the rear edge of the diffuser. This is how far the lip of the diffuser extends beyond the rear fiberglass shell. This is probably going vary by .25 inches from car to car based on how well everything matches up for the fit between the diffuser and the edges of the body shell.
I used painter's tape to lay down a strip then I marked off 1.5 inches along the rear edge with a Sharpie. The blue tape is where I masked off the opening for the transaxle housing..
There are three places I ended up having to cut the diffuser for the initial fit. There is a section of the transaxle housing that extend below the line of the diffuser. This seems pretty common for most GTM builds that I have examined. Certainly, the 991 transaxle continues to provide its share of challenges. The other place I ran into issues was the bell housing. The lip interfers with the forward diffuser edge.
This is the diffuser and the grill clamped into place to see how close I was getting on having the transaxle opening correct. This seems like the measurement should be straight forward, but it isn't (at least for me). The problem is the diffuser piece is somewhat unwieldy (I came close to dropping it more than once) and the transaxle housing is a combination of curved shapes and straight lines. In addition, you need to worry about the side ot side fitment between the diffuser and the bottom of the body shell. You can see the cardboard roller I used to assist me in getting diffuser on and off the lift.
I measured about a gazillion times and made a 6 inch square cut for the transaxle housing. I used a Rockwell VersaCut for the initial opening. I used a die grinder to make the cuts on the leading edge to clear the bell housing. To handle smoothing out the edges, I used a router table and a plunge router to smooth out the edges for the cuts for the opening. I set up the fence on the router table to handle the straight cuts for the bell housing. The other cuts I made was to widen the areas around the control arms for the suspension.
Finally satisfied with the cuts for the transaxle, I did a preliminary lay out for the louver vents. This is before any drilling, painting or bending. There is a very definite right and left side to these pieces.
All of this took several iterations between cuts and remounting the diffuser on the car. The lift proved its worth once again. I had the car about 5.5 feet high. I had a roller behind the rear wheels. This allowed me to slide the diffuser into place and to check the fitment.
These are the cuts for the vents. You need to be very precise here, because you have to be  aware of the edge beyond the body shell and running our of room as the diffuser bends around the frame. There is maybe a .25 inch fudge factor. I used the VersaCut, for the gross opening, a drill for the rounded corners and the router table to smooth and straighten everything out.
Once satisfied with the cuts for these openings, I started on the louver vents and strakes. The louvers are shipped flat. I used these as a template to determine the minimum cut opening for the louvers. I used the same method for the cuts and drilled out the corners to better provide for rounding. Next, I used the drill press to make the holes for black rivets. I purchased these a long time ago, because I think it looks really cheap to have this beautiful diffuser peppered with shiny aluminum rivets.
These are the strake and vents. Vraptor did a good design job here, because the strakes rivet to the outside and the louvers rivet to the inside. I was able to use a single rivet to fasten the louver vents, diffuser and strakes together. These are the black head rivets.
The strakes are designed to be attached with the same rivet. I used the louvers as a template for those rivet holes. The diffuser piece is easily drilled with a hand held tool. Before final assembly, I painted all parts a gloss black and opened the louver vents, by bending them open. This is really pretty easy to do, you just need to take your time.

The end result is the diffuser with plenty of venting. This is clamped in place. I will not worry about final attachment until the car is painted. I plan to go with  1/4 - 20 Helicoils for the frame and bolts and lock nuts for the body shell to diffuer connection. Some of those fasteners will be awkward, but I have a way into the underside of the car should the need arise.

Saturday, February 14, 2015

Mount Half Shafts

<< Axle and CV Joints                                         Diffuser  >>

Major System Category: Transmission
Task: Install half shafts between rear hubs and transaxle
Parts:
New Half Shafts (Custom Made)
Prerequisite Tasks:
Additional Costs: $1300
Time Requirement: 8+ hours
Date Started: November 15, 2014
Date Completed: February 14, 2015

The governing principles for Super Car Build are quite simple:
  • Failure is not an Option - Unknown
  • Never, never, never give up. - Winston Churchill
I decided that to do this job right it might take longer than I wished, and probably cost more than I anticipated. Okay. I refuse to end up as one of those guys with a half built car and a $50,000 price tag for failure.
This is an assembled half shaft per the Factory Five Manual. Looks good and it certainly would fit a G50 transaxle. But I have been off the reservation  since I went with the 991 transaxle. 
The half shafts should be a simple task. Some grunting, scraped knuckles, a few choice words, but nothing that should take months to complete. In my post on the Cable Shifter, I listed all the things up to that point that had to be adjusted for going with a Porsche 991 transaxle versus a Porsche G50. It is a long expensive list, but the end result is a state of the art, 7 speed transaxle straight from Germany. The kind of transaxle a super car deserves.
The green circles show the shaft stubs on the 991 transaxle. They measure out around 22 inches. I know you're supposed to get this stuff down to the 1/4 inch. However, there is enough play that you have some room to work with.
I assembled the half shafts with the Corvette CV joint on one end and the 930 CV on the other end. It took a little time, but it was a straight forward task. The next day, I planned to install them. I slid the Corvette CV into the Corvette hub and tried to get the other end of half shaft to connect to the transaxle. Guess what, when the shaft is several inches too long, it just isn't going to happen. The problem arises that the width of the G50 between the shaft stubs is 10 inches. The width of the 991 is 22 inches. At the time, I didn't know what the width of G50 was. I know now it is 10 inches.
This is the half axle from the Drive Shaft Shop. No, it isn't made out of gold. My buddy Brian commented that it was a beautiful unit. It is - these guys do good work.
I sent an email to Factory Five support and asked them for that dimension. They didn't know the answer. Then I asked them for assistance in specing out new half shafts. They buy their shafts overseas and couldn't help either. What about the spline count. They thought it was 28. Ever count splines by hand - you might go cross-eyed. The only thing they said was figure out the difference and divide by 2. Duh, I ALREADY KNEW THAT!
I ended up taking off the caliper, rotors, tie rod and shock absorber to get a enough room to work. My buddy Charlie chided me that I was supposed to be putting things together. In this photo, I was doing the heat - tap - heat  -tap process to get the CV splines through the hub.
If Shane (Vraptor SpeedWorks) had had a G50 sitting on the floor of his shop, he would have measured it for me. I ended up getting the dimensions from GBox. Trust me, wherever they have the dimensions posted on the web is well hidden. There are diagrams, but they are so distorted that you can't read any numbers off of them.
This bolt is the correct size and that is the Torx head I needed to install it.
I don't know what caused me to check, but I decided to see if the bolts fit. Of course not. Porsche in their modern transaxles have switched to a M10 x 1.0 mm thread. These are about as common as the proverbial unicorn at the end of the rainbow. I tried finding these on my own, and finally called Carousel Porsche Audi in Golden Valley, MN (where I had the Boxster serviced). They ordered me 12 bolts designed for the 991 transaxle. And I thought I was home free, I was just getting in line for another smack across the head.
My weapon of choice (eh, I mean tool) to get this monster assembled.
The assembled half shaft with CV joints on both ends is smidgen over 30 inches long. The actual shaft if 23 inches long. This means I needed a half shaft that was 17 inches long before I added the CV joints. I probably double checked this measurement 100 times. I knew this was not going to be cheap. I ended up ordering custom half shafts from the Drive Shaft Shop. It is a good thing they knew their business, because I certainly was swimming in the deep water. He told me how much it was going to cost. I swallowed hard and gave him my VISA info. They were on the door step in two days. These guys do really good work.
This is a beautiful sight. Normally, it takes about 20 minutes to get here. I had a minor 4 month detour.
So now I have the bolts and the half shafts. Everything should work - right? The first problem I run into is that the splines on the Corvette CV joint are new (versus the ones I got from Fparts on the donor pallet - that seems like a million years ago). The spline is correct, but these buggers are really, really tight. There is a new hardware store 3 miles down the road from the NSMC. The dog and I ended making two trips that day. The first one was to buy a torch.
Installed! I was on top of the world, and greatly relieved that it finally worked.
I used the torch to heat up the hub and heat up the end of the Corvette CV that goes through the hub. It took about 15 - 20 minutes on each side to heat, tap lightly with a hammer, heat - tap -heat - tap. The Corvette CV joints that came with the donor pallet use a 34mm nut. I had purchased a 34 mm socket. The nut required for the new CV uses a 36 mm socket. No, I didn't have one of those behemoths handy. This precipitated trip #2 to the hardware store. The pup was beginning to think I was insane.
Bracket installed on the chassis to reinforce the area that I had to remove material from.
Back at the NSMC, I believe I see light at the end of the tunnel, or it could be an in bound train. It was a train. I get lift to the proper height, I position CV and I can't get there from here. The problem  is the cradle I built for the transaxle to keep the drain plug safe. I did this, because I didn't want to cut into the chassis. <Sigh>. The only way to make this work is to cut into the chassis. Out comes the cutting wheel and angle die grinder.
Another look at the channel brace I built.
A long time ago, my dad was faced with a similar problem. A building inspector decided that two 7 inch logs was not sufficient to support a structural truss. This was a bunch of hooey, but dad was also driven to get this house built. A few days later he showed up with channel braces that distributed the load else where. I adopted this idea, and created a sleeve to reinforce the area where I cut away material. My dad was a brilliant engineer. I'm just a kid using his idea. I built the sleeve and removed the cradle. Now the everything should fit - right? Nope.

Those bolts that I special ordered from Porsche -  they were short. However, I had one thing that I never had when I looked for those bolts on my own - a Porsche part number. I maintain an office at the NSMC. So I sat down and brought up Pelican Parts. I found the bolts for the 991 transaxle (M10 x 1.0 x 46mm). I also saw in the related listing transaxle bolts for 997 transaxles. A different part number. I clicked on that link and discovered that Porsche changed the bolts when they went to the 991 transaxle. The older bolts are M10 x 1.0 x 50mm. Well what did I have to lose, I ordered 12 bolts. (I have  acquired several sets of bolts that do not work in this application.) I was already a gazillion bucks over budget on this task, what's another $20. My dad was driven to build a house; I'm driven to build a car.

The new bolts arrived. I tested them in the transaxle and they were the correct thread and pitch. They were long enough going through 930 CV. I hooked up the air ratchet and attached the biggest Torx bit I have. Literally, 20 minutes later I had everything attached!

"Never, never, never give up!"
Search Engine Submission - AddMe