Saturday, March 16, 2013

Power Cell Wiring (Final Draft)


<< Mount 3 cell kit                                           Mount INMotion Cell >>

Major System Category: ISIS Wiring
Task:Finalize ISIS Schematic
Parts: N/A
Prerequisite Tasks:
Additional Costs: N/A
Time Requirement: 10 hours
Date Started: March 5, 2013
Date Completed:  March 10, 2013
ISIS is a microprocessor based electrical system that has decentralized the fusing to power cells. Each power cell handles 10 circuits. Each circuit is fused at the power cell. The power cells are connected to a master cell (which is really nothing more than a traffic cop for signal processing between power, peripherals and switches) via a data bus. This electrical system (as is true with most vehicles) is separate from the ECU system that handles engine sensors, feed back and gauge related measurements. ISIS manages the lights, the door locks, power to the windows and mirrors and so forth.

I have been kicking around the ISIS wiring schematic for over a year now. I put the first draft up in the planning phase in October 2011. Those drawings were fairly crude renderings of where I was headed. The problem is that until I got my hands on the hardware and had completed the build to point where I had the body shell installed and recognized where I could and could not run cables, none of it clicked.

I understand the basic concepts. I can wire and splice and hook connectors together. I can connect my little test battery and see things light up or solenoids fire. What clarified my understanding was handling the physical cables for the master and power cells, comparing this to the basic wiring spreadsheets and recognizing that the wire colors were not ramdom, but had a very specific coding pattern to them. It may seem obvious to others, but once I understood the pattern everything clicked.

This post deals strictly with the power wiring schematics. It does not address the bus, mega fuses, additional modules (e.g. inReserve, inLighten, inVironment). I will cover these issues in separate posts. At present, the current system supports 40 circuits, and 39 are defined.

There are four power cells, plus a master cell. As of this writing, I have 2 power cells and a master cell installed on the car. I started with the basic 3 cell kit and the basic GTM set up.

Power Cell 1 wiring schematic. The following chart explains the wiring diagram. Color code matches the ISIS standard. (The only exception is circuit #5 where I used gray instead of white so it would be visible.) This projected over the front of the GTM chassis. The square that feeds all wires is the power cell box and reasonable represents where I have located it in the car.

Function
Power cell
connector
Circuit
fuse
Power cell wire
Right turn signal (front)
1
B
1
15
brown
Left turn signal (front)
1
B
2
15
Violet
Ignition
1
b
3
25
light green
starter
1
b
4
20
light blue
headlights
1
B
5
20
White
Fog lights
1
A
6
15
Yellow
High Beams
1
A
7
20
Blue
DRL
1
A
8

Green
Horn
1
A
9
10
Orange
Fan Override
1
A
10
25
Tan



Function
Power cell
connector
Circuit
fuse
Power cell wire
Right turn signal (rear)
2
B
1
15
brown
Left turn signal (Rear)
2
B
2
15
Violet
brake
2
b
3

light green
Left seat heater
2
b
4

light blue
right seat heater
2
B
5

White
parking brake
2
A
6

Yellow
Rear sensors
2
A
7

Blue
Fuel Pump
2
A
8

Green
tpms
2
A
9

Orange
Hatch popper
2
A
10

Tan

Power Cell 3 wiring schematic. The following chart explains the wiring diagram. Color code matches the ISIS standard. (The only exception is circuit #5 where I used gray instead of white so it would be visible.) This projected over the front of the GTM chassis. The square that feeds all wires is the power cell box and reasonable represents where I have located it in the car.
Function
Power cell
connector
Circuit
fuse
Power cell wire
right window up
3
B
1

brown
right window down
3
B
2

Violet
left window up
3
b
3

light green
left window down
3
b
4

light blue
left door popper
3
B
5

White
right door popper
3
A
6

Yellow
telescoping steering
3
A
7

Blue
hot plug
3
A
8

Green
front sensors
3
A
9

Orange
Map Lights
3
A
10

Tan

Power Cell 4 wiring schematic. The following chart explains the wiring diagram. Color code matches the ISIS standard. (The only exception is circuit #5 where I used gray instead of white so it would be visible.) This projected over the rear of the GTM chassis. The seat heaters is an approximate location inside the cockpit. The square that feeds all wires is the power cell box and reasonable represents where I have located it in the car.
Function
Power cell
connector
Circuit
fuse
Power cell wire
escort 9500 ci
4
B
1

brown
ars global
4
B
2

Violet
homelink
4
b
3

light green
wiper
4
b
4

light blue
side mirror
4
B
5

White
interior lights
4
A
6

Yellow
hot plug
4
A
7

Blue
cruise control
4
A
8

Green
dash/Parking
4
A
9

Orange

4
A
10

Tan



Monday, March 11, 2013

Transaxle Purchase

Early on in the planning stage I needed to make a decision between a Porsche G50 or a Mendeola SDR transaxle. Those were the choices. A great deal of discussion has taken place on the Factory Five Forums regarding these options. The G50 can be had in either 5 or 6 speed configurations. There are multiple gear ratio packages and kits to make sure transaxle runs inverted.

The Mendeola was plagued in the early days with delivery problems, but those seem to be old news. There are rumors of a 6 speed version. However, the production runs have been and will be limited runs. The SDR transaxle is a market opportunity as the G50 transaxles were scooped up for various build projects.

The transaxle doesn't exist in a vacuum  There are additional parts that need to be purchased:

  • Flywheel
  • Clutch release components
  • Stage II Clutch
  • Cable shift Assy
  • Pump and cooler kit
  • Bolt Kit
  • Gear Reduction Starter 
The additional parts cost around $5000. I built the budget based on major systems for the car. The transaxle plus these parts represent the second largest cost for the build.

Transaxle cost works out as follows:
  • A properly rebuilt G50 set up for inverted use costs around $9000.
  • A new Mendeola SDR costs around $11,500.
I opted to go with a new Mendeola transaxle. My feeling was that there was less to go wrong with a new transaxle than a rebuilt one. I specified a Mendeola transaxle when I ordered the chassis from Factory Five.

Then I changed my mind.
Seven forward speeds. Two more than the SDR. One or two more than the G50. Factory new (and as of this writing) on a slow boat from Germany.
One of the benefits of not having all the money up front is that I can leverage changes in technology over the three years this is going to take to complete.

Early in 2013, Eric at Gbox posted a thread on the Factory Five forums asking if anyone was interested in a 7 speed 991 transaxle. The same transaxle that is in the new generation Porache 911.

My neck still smarts from the whiplash. Say what!?! Brand new, shipped from Germany, 7 speed Porsche transaxle!!!!

Good bye G50.

Good bye SDR.

Hello 991!

I am bouncing off the walls.
Gbox puts all the parts together and test beds it on an LS block before it leaves their shop for the Northern Man Cave. It is a brand new transaxle that is currently shipping in the 991 generation of the flagship Porsche 911s.

The bad news is this busts the budget. The 991 costs $13,500. Ouch!

Or does it?

One of the items high on the design list were paddle shifters. I contacted Master Shift (my vendor for the aftermarket paddle shift solution) and asked if they had done anything with a 991 transaxle. The answer was no. They had done a 7 speed pattern for a different transmission. I chewed on this for a  couple of weeks. I decided that I did not want to be the Mark I version for an aftermarket paddle shift solution. With great reluctance, I dropped the paddle shifter from the design plan and gained $3000 back to the budget.

The SDR option has the following costs:

  • SDR - $11,500
  • Additional Parts - $5000
  • Paddle shifter = $3000
  • Total cost is $19,500 plus shipping
The 991 option has the following costs:

  • 991 - $13,500
  • Additional Parts - $5000
  • Total cost is $18,500 plus shipping

By dropping back to tradition bump shift and going with the 991. I am $1000 below the cost of a new SDR with paddle shift. This isn't funny money like what happens in Washington. This is my pocket book.

Originally, I had hoped to do the engine and transaxle in 2013. That is no longer going to happen. My concentration this year is the rest of the car and the transaxle.

As my wife's cousin said, "Someone is going to have some fun!"

I certainly am!

Side Mirrors


<< Door Poppers                                             Next >>

Major System Category: Body (Door)
Task: Install side mirrors
Parts: Corvette donor side mirrors.
Prerequisite Tasks:
Additional Costs: N/A
Time Requirement: 4 hours
Date Started: November 21, 2012
Date Completed:  November 25, 2012
The side mirrors installed very easily. Basically, you follow the measurements in the manual, use the gasket as a guide, mark and drill the holes. After that it is just a matter of screwing the mirrors tight.
Driver's side side mirror. the passenger side one is silver. So right now I have yellow, red and silver car. Note the three mounting studs and power cable. The mirrors were part of the donor car kit I purchased from FParts.
The main power cable has a grommet that is taped in place. I removed the tape and measured the location of this hole between the 3 studs. This hole has to be somewhat close otherwise the cable tends to bind. I also had to ensure the hole was not too big as I wanted the grommet to maintain a water tight seal.
These are the holes drilled for the studs. I was a little bit off, so I had to open up one of the holes to get the mirror to mount. Otherwise there were no problems. The "X" marks the location for the power cable.
There is the issue of hooking up the mirror for power and control. I have decided to go with the Quick Racing Products power mirror harness kit. The alternative was to work out something using a Corvette based control panel or to hook it into ISIS.
This the grommet on the power cable.
I decided against purchasing a mirror control panel on Ebay. If I went the Ebay route, I would still be faced with the interface to the mirrors. Not impossible, but the QRP solution already solved that problem. There is enough invention on this car, without finding more.
I made sure the grommet is properly seated prior to mounting the mirror. This is pretty much idiot proof. Just take your time, measure and make sure everything looks okay.
ISIS was another solution, However, the beauty of ISIS is its limitation in this case. I would have to use an InMotion Cell. This would have required eight circuits to handle the up down and side to side motion on each mirror. That would be a lot of wiring for something that a relay can handle so much more elegantly.
Some shameless self promotion!
Jay Harris (President of ISIS) had talked about a special module to handle the mirrors, but couldn't find enough interest. Jay is good guy. He will work with you, answer your questions. He even answers the phone! He told me flat out that most people were going with a QRP type solution. Easy enough. It is not like I am not going to spend a fair chunk of change on his stuff, but I appreciate his honesty.
Mounted!

Search Engine Submission - AddMe