Showing posts with label cost savings. Show all posts
Showing posts with label cost savings. Show all posts

Friday, July 6, 2012

Protective coat on external sheet metal parts


<< Kit Disassembly                                                                        Next Link >>


Major System Category:
Task: Deploy additional coating to protect exposed sheet metal (optional)
Parts: All sheet metal parts
Prerequisite Tasks: Remove parts from chassis
Additional Costs: Powder coating ($250 - $500), DIY ($60 -$120)
Time Requirement: Off and on over several days
Date Started: July 2, 2012
Date Completed:

There are couple of ways to go with this. If price is no object, then take everything off the chassis and have it professionally powder coated. You will get a tough, durable coating. If this is a $50,000 project, then do nothing. If you land somewhere in the middle, you can separate the parts into those that will be exposed to the elements and those that comprise the tunnel, and just powder coat the external pieces. There is one other alternative.

The first thing you're going to do once you get the panels back from the powder coat shop is start drilling holes into that beautiful baked on finish. You will develop scratches in the powder coat, because a drill will slip or something will bang against it. If you're like me, this will drive you CRAZY. I have drawn a fair amount of attention from the neighborhood since the GTM arrived. Plus I'm the only guy on the block with a four post lift. My neighbor Ron suggested I might want something other than powder coating that could be repaired. So I did some research.
This is the spray can version. It takes a while to shake up, because it is really thick. A can does not go that far either. It is about 25% the cost of powder coating.

Plasti Dip is a rubberized coating that can be sprayed or brushed on to a surface. The label warns you to do this in a well ventilated area - they aren't kidding. This stuff has a real paint smell to it. NAPA
carries this stuff, although they may have to get it from the warehouse. I found that if the warehouse had it on hand, I could pick it up by 2:00 PM. (We have a great Napa store in Corcoran, Minnesota!) It comes in black, camo, smoke and clear.
This is the LH inner wheel well prior to being riveted to the chassis. It has been coated with Plasti Dip. This is a dull black finish. Since most of this area is hidden from view by the awesome tires and super duper paint job, who really cares if it is dull or shiny.

Here are the benefits from this approach:
  1. Cost is approximately 25% of powder coating.
  2. Panels never leave the build area. (This is a big for me. There are many parts and some are easy to misplace.)
  3. Rubberized surface cuts down on noise. 
  4. Repairable.
Here are the draw backs:
  1. It is not as pretty as a shiny powder coated surface.
  2. It is not as durable.

Sunday, October 9, 2011

GTM Radiator

I got around to unpacking the radiator for the GTM. This is a stock OEM replacement radiator designed for C5 Corvette.
I went with a stock radiator for the following reasons:
  1. My experience with the C5 under 100 degree temperatures in traffic idle situations. This the same set up as what will be installed into the GTM. Engine cooling runs up to around 230 degrees, then the fans kick in and she goes back to 215.
  2. Fitment issues with the current GTM chassis. Alternative radiators (e.g. DeWitts, BeCool) have a bigger footprint. I am planning enough deviations from the standard spec on the car that I really do not want to deal with an additional issue. If/When I get into trouble, I can always go back to look at the Corvette and see how everything is put together.
  3. I do not plan to race the car, so I see little upside benefit for a radiator costing $400 - $600 more and requiring additional work to get it installed.
  4. I have other places where i want to spend money (some glamour / some performance / some just plain fun).

Tuesday, October 4, 2011

58x Crankshaft Signal Converter

When I purchased the donor kit from FPARTS (see posts Donor Parts Kit (purchased), Donor Parts Kit Arrives, Donor Parts Kits (Catalogued)), I received an engine harness and PCM for the LS1 engine. However, I plan to purchase a LS376/480 crate engine and this presents a problem.

The LS1 engine harness and PCM are not compatible with the LS3 engine. The reason for this is the LS1  is a Gen III engine and the LS3 is a Gen IV engine. This change took place when in 2006. The major problem is the Gen III engines us a 24x reluctor wheel and the Gen IV engines use a 58x reluctor wheel. This is the crank signal protocol. Basically, a 58x signal does not work on a 24x harness and vice versa.

The oddity is the 2005 Corvette (the first year of the sixth generation Corvette) in that it has a LS2 Gen IV engine with a 24x reluctor wheel.

My initial thoughts were that once I got everything running on the GTM with the LS3 engine, I would run to Ebay and put the LS1 harness up for auction. Conservatively, the engine harness and PCM represent about 20% of the donor kit cost, plus the cost of a new harness and PCM compatible with the LS3 is around $1800 - $2000. That's a swing of $3000 - OUCH!

There's a better way. I read in  GM LS-Series Engines: The Complete Swap Manual that Lingenfelter Performance Engineering makes 58X - 24X Crank Sensor Trigger Conversion Module.
For $250, I can purchase a plug & play module, salvage my investment and save $2000.

Thursday, June 2, 2011

The Donor Car - Part 2

The donor car is a cost effective method for acquiring the parts needed for the build. The donor is a cadaver that will never roar down a twisting country road again. So you have to ask yourself what happened. The car either was the victim of a flood, theft or crash. (Stay away from the fire damaged ones. The reasons become obvious, once you look.) The insurance company deemed it unrepairable, and that means there was in excess of $20,000 damage to the vehicle. This number is based on the current replacement cost for a low end Corvette C5.

The major subsystems provided by the donor are as follows:
  • Front suspension
  • Engine
  • Rear suspension
  • Rear CV joints
  • Emergency Brake Assembly
  • Fuel Delivery
  • Cooling system
  • A/C 
  • Brakes
  • Miscellaneous (basically everything else)
Factory Five says the donor needs to be a C5. This is the path of least resistance, but many of these subsystems are common across generations for years 2003 to 2009. There is a substantial financial argument to be made for donor with a working engine.

My perfect donor is as follows:
  • 2008/2009
  • Larger wheels (18 front / 19 rear) - I'd scavenge these for the Big Yellow Toy.
  • Big brake upgrade
  • LS3/LS7 engine
  • Intact suspension
  • Intact instrumentation
This poor thing has too much damage for the GTM project. My first clue was lack of wheels and anything to hold them along the driver's side. The love of my life has already indicated that I need to make sure the wheels stay on the car.

This car on the other hand got hit on the passenger side. There is a substantial mess inside, but the mechanicals look good.
As I said, there is a substantial cost savings going the donor car route. The opportunity to acquire a working LS3 or LS7 engine plus the majority of the parts needed for assembly needs to be considered. Copart and Ebay are the easiest places to look for salvage or unrepairable titled cars.



    Search Engine Submission - AddMe