Showing posts with label super car. Show all posts
Showing posts with label super car. Show all posts

Monday, February 18, 2013

Door Poppers


<< Door Latch                                           Side Mirrors >>

Major System Category: Body (Door)
Task: Install door poppers
Parts: Popper solenoid, cable, pulley
Prerequisite Tasks:
Additional Costs: $75
Time Requirement: 4 hours
Date Started: November 21, 2012
Date Completed:  November 25, 2012
One of the issues I worry about is security. These cars attract a lot of attention. Chances are people have never seen a GTM.  I decided to go keyless early in the planning stage. This means the normal form of ingress (i.e. door handles) needed to go away. I'm not going to go into detail on the security system, except to say it is multi-layered and bio-metrically keyed to me. Yes, if I have a dead battery, she's going to be hard to start.
These are the pulleys and the solenoid base plate.
The first security layer is to eliminate door handles and rely on door poppers to open the door. There is a need for a manual override, and I have something in mind for how I am going to put that together. To operate the poppers I have a fob. The fob is linked to the RFlink module installed in the ISIS master cell. However, the fob can only get you into the car. It has nothing to do with starting the car.
The rear of the solenoid where I attached power and ground leads. This is clamped in a vice. I did  all the electrical work down stairs in my cave, as the temperature was dropping through out December.
I am using 60 lbs solenoid door poppers and a plungers to push the door open past the striker. The plungers (like the striker) need to be installed after the engine and transaxle are installed. The plungers need to be secured against the chassis and installed through the body shell.
The solenoid popper is bolted to the mounting bracket. The steel cable is looped around the end of the solenoid and the clamp is in place, but not compressed. Yes, they don't make vices like this any more. It was purchased 60 or 70 years ago.
The latch has a vertical orientation. The idea behind the popper is a solenoid attached to a wire cable that fires (i.e. contracts) been an electrical charge is applied. Unlike the rear hatch popper, it is not possible to position the solenoid so it is in a straight line to the latch.
Close up of the pulley with the steel cable threaded. At this point nothing had been tightened down, so that is why there is slack on the line. The pulley is riveted into place. You can also see the narrow end of the internal brace. Things are very tight on the rear edge of the door.
The solenoid works on a electrical charge that fires the solenoid causing it to contract into the housing. I attached five feet of 16 gauge wire for power and ground. This has to be threaded out of the door and into the front hood area where it gets connected to the power cell and grounded at a ground point on the chassis.
The popper solenoid and pulley before the steel cable is tightened into place. The cables from the window motor is just to the right of the popper solenoid and the black bracket in the middle of the photo (behind the brace) is the window track.
I use a 12 volt test battery to verify the connections are working and that they are solid (this is a lot of fun - it's a guy thing). The solenoids come with a heavy bracket. This is mounted to the bottom of the inside of the door. I used short bolts and nylon nuts to secure it in place. The last thing I want is for the popper solenoid to slide loose inside the door.
Everything is tightened up. Note: There is still some slack in the steel cable.
The idea to use a pulley and form a right angle between the latch and the popper solenoid is not original with me. I don't remember where I first saw the idea, but it really works. The pulleys are quite simple (a $2 part at Lowes). I think I found them in the screen door section. The pulley allows me to create a right angle between the popper solenoid and the latch. I riveted the pulley into place and checked for strength.

I threaded the steel cable from the latch, through the pulley and to the popper solenoid. The cable loops around the solenoid end and is crimped using the two channel clamp. If you lose one of these clamps, there are available at the little parts area where they sell pulleys at Lowes and Home Depot.

Once everything is tightened down, I retrieve my test battery and fire the solenoid. There is plenty to check:
  1. The door latch actually opens.
  2. The pulley doesn't stress.
  3. The bracket holding to solenoid doesn't stress.
I fired the solenoid about twenty times. There is a significant bang each time. 

Tuesday, July 10, 2012

Rear Suspension Mounting to Chassis


<< Rear Splash Panels                             Rear Tie Rod >>
                                        Emergency Brake and Cables >>

Major System Category: Brakes & Suspension
Task: Attach Corvette rear suspension to mount points on chassis.
Parts:
  • Rear suspension
  • Small jack
  • Jack stands or blocks
  • The Hulk (if available)
Prerequisite Tasks: Rear Splash Panels
Additional Costs: N/A
Time Requirement: 90 minutes (less if you have a big buddy)
Date Started: July 10, 2012
Date Completed: July 10, 2012
Last fall I purchased the Z06 big brake upgrade kit from West Coast Corvettes. I was really excited, because these were the first pieces of the car I could actually put together. These brakes are massive and heavy. The suspension is massive and heavy. I put these parts together and created a heavier assembly. I think it is easier to assemble the brakes on a bench than on the car, but that's my opinion.
The LH rear suspension resting on the lift next to the yellow floor jack. This is another case where the lift  makes a task easier for a one man shop. I lowered the chassis to a comfortable working height.
 Up to the point of purchasing the brakes, all I had to show for my project was a crate of used Corvette parts taking up space in the basement. Last October I added the assembled brake kit, then the wheels. This is now why I now have an off site storage locker. This is all to say, the suspension assembly I worked with can be made lighter.

Rear suspension mounted on the left hand side of the chassis and supported by a jack stand. The Z06 brakes  look very nice. A point of interest: the LS7 powered GTM reviewed by Car & Driver was equipped with this brake package.
I started with the left hand assembly. This side required some persuasion as the mount points were a tad tight. A couple of judicious taps from a 10 lbs sledge and they opened enough to slide the control arm ends into the place. I also employed a small floor jack. This I got under the knuckle. This was helpful as I could move the assembly around. You need to get it dead on so it matches up with the geometry on the chassis. The right hand side went easier. The last thing I did was lower the assembly on a jack stand (blocks work too). The alternative is to just let rest on the floor. I didn't want to do this.

Radiator Install


<< Radiator Aluminum                                                    Coolant Lines >>

Major System Category: AC & Cooling System
Task: Secure Radiator assembly to chassis
Parts:
  • Radiator
  • Fan Assembly
  • Air Conditioner Condenser
  • Rubber Isolators (LH/RH)
Prerequisite Tasks: Radiator Aluminum
Additional Costs: N/A
Time Requirement: 30 Minutes (maybe a little longer if you have find some bolts)
Date Started: July 8, 2012
Date Completed: July 8, 2012
The radiator install was a breeze. Since my car will have air conditioning, this involved clipping together the air conditioner condenser, the radiator and the ran assembly. These parts are idiot proof. There is only one way to put these pieces together.
This assembly clips together. Once you have the orientation correct, it takes maybe a minute to connect things.
I test fitted the radiator assembly in place prior to finishing the radiator aluminum. I did this to make sure everything fit okay. I was a bit leery about going with a bigger radiator and purchased a brand new stock Corvette radiator. My experience in heavy summer time traffic or parades is that the stock radiator is more than adequate for a street car.
This is a side view of the clips. The air conditioner condenser  is facing .

Additional side view of the assembly.

Design Change: The build manual says to drill the frame of the radiator and rivet it to the three tabs om the front of chassis. (This is obvious when you are looking at the car.) I wasn't comfortable riveting a radiator into the car. I may decide to upgrade down the road, so I went down to my junk box and found two bolts with slip rings. I added Blue Loctite as a thread locker. This radiator is not going anywhere, but it can be maintained.
Rubber isokators (LH/RH) as packaged from Fparts.
LH isolator. The nipple needs to be removed.
After nipple is removed.
Entire radiator assembly installed on the chassis.
Bolted, not riveted, into place.
On the issue of maintenance, I think builders need to think about how certain tasks are going to be accomplished. When I work on the Boxster, I usually have to take apart a good part of the undercarriage to gain access to various systems. I want to make sure, I have ease of access to all systems on the GTM.

Saturday, July 7, 2012

Battery Tray


<< Steering Rack                                                                             Next Link >>


Major System Category: Body (Undercarriage)
Task: Install battery tray
Parts: Battery Tray
Prerequisite Tasks: Steering Rack
Additional Costs: N/A
Time Requirement: 30 minutes
Date Started: July 7, 2012
Date Completed: July 7, 2012

This is a very straight forward task. By now you know if you are installing air conditioning. If so, you are going to use the off set described in the manual to place the tray closer to the driver's side. You want to make sure that when you eye ball the tray location so it clears the steering rack and cross members. You need to think about how the battery will be changed and/or installed. Due to space and weight considerations, I will be installing an AGM style battery.

Battery tray rough placement as seen from under the car. Steering rack is towards front of car.

Lines marked for placement with air conditioning.
Sprayed and drilled. Ready for install.

Steps required:
  1. Coat the tray (optional).
  2. Place the tray.
  3. Trace the lines.
  4. Drill the holes.
  5. Apply silicone.
  6. Rivet to chassis.
  7. Overspray rivets to black (optional).

Friday, July 6, 2012

Protective coat on external sheet metal parts


<< Kit Disassembly                                                                        Next Link >>


Major System Category:
Task: Deploy additional coating to protect exposed sheet metal (optional)
Parts: All sheet metal parts
Prerequisite Tasks: Remove parts from chassis
Additional Costs: Powder coating ($250 - $500), DIY ($60 -$120)
Time Requirement: Off and on over several days
Date Started: July 2, 2012
Date Completed:

There are couple of ways to go with this. If price is no object, then take everything off the chassis and have it professionally powder coated. You will get a tough, durable coating. If this is a $50,000 project, then do nothing. If you land somewhere in the middle, you can separate the parts into those that will be exposed to the elements and those that comprise the tunnel, and just powder coat the external pieces. There is one other alternative.

The first thing you're going to do once you get the panels back from the powder coat shop is start drilling holes into that beautiful baked on finish. You will develop scratches in the powder coat, because a drill will slip or something will bang against it. If you're like me, this will drive you CRAZY. I have drawn a fair amount of attention from the neighborhood since the GTM arrived. Plus I'm the only guy on the block with a four post lift. My neighbor Ron suggested I might want something other than powder coating that could be repaired. So I did some research.
This is the spray can version. It takes a while to shake up, because it is really thick. A can does not go that far either. It is about 25% the cost of powder coating.

Plasti Dip is a rubberized coating that can be sprayed or brushed on to a surface. The label warns you to do this in a well ventilated area - they aren't kidding. This stuff has a real paint smell to it. NAPA
carries this stuff, although they may have to get it from the warehouse. I found that if the warehouse had it on hand, I could pick it up by 2:00 PM. (We have a great Napa store in Corcoran, Minnesota!) It comes in black, camo, smoke and clear.
This is the LH inner wheel well prior to being riveted to the chassis. It has been coated with Plasti Dip. This is a dull black finish. Since most of this area is hidden from view by the awesome tires and super duper paint job, who really cares if it is dull or shiny.

Here are the benefits from this approach:
  1. Cost is approximately 25% of powder coating.
  2. Panels never leave the build area. (This is a big for me. There are many parts and some are easy to misplace.)
  3. Rubberized surface cuts down on noise. 
  4. Repairable.
Here are the draw backs:
  1. It is not as pretty as a shiny powder coated surface.
  2. It is not as durable.

Monday, June 25, 2012

Traction and Launch Control

One of the items that the GTM lacks is traction and launch control. These are items found in top end sports cars around the world. It usually is manifested in a dial or switch that turns functionality on or off, or allows the driver to dial in the level of traction control desired. However, just as there is an aftermarket solution for blind spot assist, there is an aftermarket solution for traction and launch control.

Traction control is a computer assist to designed to keep the car on the road and under control. It accomplishes this by reducing spark, fuel supply, throttle and increasing brakes on one or more wheels.

Launch control is a computer assist designed to eliminate the human factor in launching the car from a standing start. Instead of having to balance clutch and throttle, you only have to worry about letting out the clutch.

As I have mentioned before, there is a wealth of knowledge on the Factory Five Forums. I found this in a post by Spytech. I know he's one of the frozen chosen in Minnesota, and he has had his car running for a good year now. His build log is a treasure trove.
Racelogic traction control module.

Racelogic offers an traction and launch control module, wheel speed sensors and programmable software that can be customized to for a GTM (or any other car).
The digital adjuster sets slip levels in 1% increments from 0 to 25%. Launch control is a standard feature. This available in brushed aluminum (shown) or black.

My GTM will not have ABS. I don't plan to drive her in bad weather. However not all things can be foreseen, and for a car projected to have approximately 575HP, traction control sounds like a very good idea.

The software has input screens for the following:
  • Main configuration
  • Launch Control setup
  • Slip control setup
  • Wheel channel assignments and setup
  • Rev-limits setup
  • Data-logging setup
You need a laptop to hook into the system and get things running. The software is available for download on the Racelogic website. You can get an up to date list of US distributors on the website.

It is a good thing I am going with a paddle shift system, because I really don't have any room for a conventional shift lever. I'll need to be very careful on how I map out my center console.

Friday, March 2, 2012

Carbon Fiber

I peruse a lot of GTM build sites, looking for ideas. One thing I have looked at for my other cars is carbon fiber parts. These are expensive!  The GTM stock interior is black plastic, and there are no third party vendors offering carbon fiber upgrades, So how do you incorporate carbon fiber into the GTM build ? There are a couple of options.
I plan to install fender louvers. Besides wanting these to have a carbon fiber look, I also want to have black rivets for the install. One thing that drives me nuts are these elegant pieces held on by shiny aluminum colored rivets. They just look out of place to me.

One place is located in the UK is called Carbon Mods. They sell a couple of different kits to create a molded carbon fiber part, or to cover the part in a high gloss carbon fiber cloth. This is not a vinyl product. Think of it as decoupage for car parts. This process will take about 2 or 3 days to cover a part. The result is spectacular. Personally, I would try this out on a smaller part and debug the process. I think this process would prove difficult with larger pieces. Carbon Mods has a great instructional video that explains their process.



The other place I came across is Destron's Garage. Their approach is to cover the part with a air breathable wrap made from either carbon fiber cloth (for interior products) or a UV resistant carbon fiber vinyl (for exterior products). This is an easier process and more applicable to larger pieces. These guys are very responsive. They answered both my email query on their contact pages, as well as my questions on their Face Book page. They have a decent step-by-step instructional page that explains their process.
The roof scoop is a very large piece. I figure this winter work that can be accomplished either at the Northern or Southern Man cave locations during the winter months.

The Carbon Mods approach probably lasts longer. However, my GTM will not be sitting outside in the elements fighting off rain, snow, sun shine and bird droppings. My GTM will be pampered like the Corvette and the Boxster. If I am very fortunate, I hope to purchase garage condo for the entire fleet.
Of course, no GTM is complete without a Gen II splitter. One of the planning considerations  is to divide things that can be accomplished on the chassis, and items that can be worked on in the Man  Cave during the winter months. Those living in southern climes don't have the same considerations, but a Minnesota winter can put a dent in anyone's build schedule.

I asked Destron's Garage what the life cycle was for their exterior product. They say you can expect 5 years, and if it is pampered maybe another 3 to 4. By then, I'll want to do something new to my GTM.

Friday, February 3, 2012

Parking Assist

I ordered the parking assist sensors last month. I decided to go with a 4 sensor set up for front and rear for a total of 8 sensors. Basically, you end up purchasing two 4 sensor kits. The purpose of parking sensors is to assist the driver with an audio/visual notification of obstructions within 5 feet of the front or rear bumpers.
This is one of the kits.
I already know that parking a car on the lift or under the lift will be a close thing. It is easy to park a car under the lift. It is harder to park a car going up the ramps and keep everything straight. I can park the Camry and Boxster without any problems. The minivan fits on the lift if you remove the side mirrors, so there are limitations to what I can park on the lift. The driver's rear view and perception in the GTM is minimal.
They sent me 2 sets of sensors. This is the basic set.
The sensors are  position inside the bumper fascia. This means it will be inside the fiberglass shell. Forward sensors are connected to the brake light. Rear sensors are connected to the reverse lights. You might think forward sensors are overkill, but I have discovered that parking the Corvette and/or the Boxster (with its new front end) can be a challenge as you just don't have a great sense for the distance between the front end and the curb.
This is the second set of sensirs that have double sided 3M auto motive tape.
The sensors connect to a control box. The control box is wired to a power source. Most likely with wire taps. This is very low power system. I will be employing LED lamps through out the GTM, so tapping these sensors into those circuits should be a minimal load.
Control box, power leads, buzzer and buzzer interface wire.
The control box has outlets for buzzer and display. I plan to only use a buzzer system. I will augment the parking assist sensors with forward and rear cameras wired into the stereo/Mp3/BlueTooth/GPS system on the center console. One of this year's projects is to upgrade the Boxster's electronics. I plan to add a camera to that project. I will use the Boxster as a camera test bed.
Control box with inputs for power, left sensor, left center sensor, right center sensor and ring sensor. Outputs for display and buzzer.
This set changes the ISIS wiring setup. At the time, I reasoned the parking assist required a separate circuit. Since this system is designed to piggyback on lighting circuits, there is no need for a separate ISIS circuit. The other change to the ISIS wiring diagrams is the elimination of a separate circuit for HomeLink. Since I am going with a GPS Navigation system on the center console, I can move HomeLink functionality to the rear view mirror.




Thursday, November 17, 2011

Garage Prep III

This is the final phase for garage prep prior to ordering the GTM chassis. I installed a Swisstrax floor at the build site. In the post entitled Synergy I discussed Swisstrax flooring. If you decide to install a floor like this, list Traci as your sales person. She has handled 4 orders for me, and they all arrived perfect.

Finished product. The Maple Grove build site for the GTM.

Neither the Swisstrax floor or the DirectLift car lift are requirements for the GTM. They are both designed to make the build space more usable. The Swisstrax floor is virtually indestructible. It doesn't mar from jack stands or ramps. It doesn't come apart when a car drives on/off repeatedly. It doesn't fade under bright sun (and South Carolina has plenty of that). It doesn't scratch your painted parts.

DiamondTrax tile.
Each tile is a mixture of polymers and rubber, and each tile has a compression strength of 5120 psi. This floor is more forgiving than concrete, and I have no illusions - things will get dinged and nicked during the build. Hopefully, the Swisstrax floor will mitigate some of my clumsiness.

This is the bottom of a tile. You can see it is designed to handle a significant load. In my case, the weight of the lift is dispersed to four load points and the weight of any car I might put on there is equally distributed to those load points. The lift weights 1700 lbs and the heaviest car I might put up there is 4000 lbs. That comes down to 1600 lbs per load point - well within spec for the titles.
I chose the DiamondTrax pattern, because it provides grip and prevents things from just wandering away. It is available in fourteen colors. Once you've selected the product and have measurements, go to the floor designer and build your floor. The designer is a HTML WYSIWYG tool. When you're satisfy request a quote. Get the estimate, pay the bill and wait for FedEx truck to arrive.

Th edge pieces are about 2 inches wide and provide a nice ramp edge to the floor.
Assembly is a snap. The tiles fit together per the plan you submitted. For tools you need some gloves, knee pads, rubber mallet and a cutting tool (I'd suggest the Dremel Multi Max or one of its clones). I finish off the job with end pieces to give me a tapered edge.

Friday, October 28, 2011

Big Brake Upgrade - October 2011

The big brake upgrade requires that you go with 18 inch wheels or larger. This means you are making commitment to a larger wheel size (and the incumbent costs). According to Factory Five Tech Support, this is the same brake package they installed on their LS7 powered test mule that did 0 to 60 in 3.0 seconds.
Z06 C5/C6 Big Brake Upgrade Kit

The stock C5 Corvette front/rear set up is 17 and 18 inches respectively. This is not large enough to accommodate this package. This package requires 18 inch wheels (minimum). Some vendors will warn you about this on their websites. West Cost Corvette had the best price. As I have purchased other major systems for the my Corvette from them, I felt comfortable making this purchase. The Big Brake Upgrade includes the following:

  • (2) 6 piston front calipers
  • (2) 4 piston rear calipers
  • (2) drilled and slotted 14 inch front rotors
  • (2) drilled and slotted 13.4 inch rear rotors
  • (1) set HAWK Z06 front and rear HPS brake pads
  • (4) DOT steel braided brake lines   
  • (4) pints Motul Racing Brake Fluid

In the overall budget, I allocated a separate line item for this package.

Left side front/rear suspension
This is an enhancement to the overall build, and I can complete it prior to ordering the GTM chassis. The suspension is no longer connected to the rest of the car, so you need to brace it.
These 22mm bolts turned very stiffly. They were the biggest problem I encountered.
The first thing you need to do is loosen the 22mm bolts that attach the caliper pistons to the knuckle. Warning: These bolts haven't been turned since the donor car left the factory, and the rear suspension ones seemed to have been tightened down by Godzilla. I was using an old torque wrench as a breaker bar. It went past 150 foot pounds (end of the scale), and I only got tired. 

I clamped down the suspension, sprayed the bolts with penetrating oil, tapped them lightly with a hammer, and used a 20 inch breaker bar. You may have to repeat this a couple of times. Give the oil some time to work (at least 15 minutes). There were some comments from the management that the oil stinks. You can't keep everyone happy.

Crush washer.

Second, you will find crush washers on the front rotors. Use a small screw driver and needle nose pliers to get the free. You don't really need them. There are none on the rear rotors.
The new rotor is on top. You can see it is a larger diameter and it is drilled. 
Third, slide the caliper off and pull the rotor off. For the most part these just slide right off, but a couple of them required some persuasion. While the rotor is off, I took some Rem Oil and steel wool to clean up the surface rust on the hub.
Thread the 22mm bolts back on.
 Fourth, slide the new rotor and caliper on the hub. Insert the 22mm bolts back into the caliper. I plan to wait until the suspension is mounted on the chassis before torquing to spec (125 ft-lbs).
There is a pad for each piston. Six pads for each front caliper and 4 pads for each rear caliper.
The penny is there to give you an idea on large these are.
Fifth, insert pads right through the top of the caliper. The pads are head in place by bolts that slide into the half moon notch on the side of the pads. The bolts are stainless steel that screw in using an Allen wrench.
Top down view on caliper. There is a pad installed on the right side, and the left side is still open. You can see the stainless steel bolt and piston on the left hand side.
It takes about 5 minutes to put these pads in. Probably a little longer, once the suspension is mounted on the chassis. This is easier than playing around with two wrenches and swinging the caliper up to replace the  pads.
Remove the plug and install the braided steel brake lines.
Sixth, we need to attach the braided brakes lines. This is very easy. This connect to the reservoir on the back of the caliper using a banjo bolt.
Banjo bolt and end of the braided brake line.
This was pretty easy to do. Once I figured out how everything fit together, the second brake/rotor went very fast.
Finished product.



Sunday, October 9, 2011

GTM Radiator

I got around to unpacking the radiator for the GTM. This is a stock OEM replacement radiator designed for C5 Corvette.
I went with a stock radiator for the following reasons:
  1. My experience with the C5 under 100 degree temperatures in traffic idle situations. This the same set up as what will be installed into the GTM. Engine cooling runs up to around 230 degrees, then the fans kick in and she goes back to 215.
  2. Fitment issues with the current GTM chassis. Alternative radiators (e.g. DeWitts, BeCool) have a bigger footprint. I am planning enough deviations from the standard spec on the car that I really do not want to deal with an additional issue. If/When I get into trouble, I can always go back to look at the Corvette and see how everything is put together.
  3. I do not plan to race the car, so I see little upside benefit for a radiator costing $400 - $600 more and requiring additional work to get it installed.
  4. I have other places where i want to spend money (some glamour / some performance / some just plain fun).

Wednesday, August 10, 2011

Donor Parts Kit (Cataloged)

The donor parts kit was the most practical approach for this phase of the build. I do not have space for a donor C5, plus storage for GTM components. I had already decided that I was going with a bigger engine than the LS1, and I plan to purchase the big brake upgrade kit. Those decisions make a donor C5 impractical.  Photos are here.

I purchased the kit on Ebay from Fparts. Fparts is a salvage yard located in Bristol, PA. They specialize in Firebird, Camero and Corvette salvage. According to their banner, they put together more than 25 of these kits in 2008.

The first thing you need to understand is the kit is not sitting around on some skid, waiting for you to put your money down. These parts are still installed on existing vehicles. They even apologized that it took them a week to get things together. It would probably take me a month.

The second thing is this is going to come via freight. The shipping company provided a tracking number, and I was able to follow my skid from Pennsylvania to Minneapolis. The day before it was due into the Minneapolis terminal, I called and set up a delivery time. I did have to pay extra for a lift gate truck. If you have the means to pick it up yourself, you can save $50.

The third thing is the parts are used. However, you have to understand the Corvette mindset. Since I have a C5 and belong to Myrtle Beach Corvette Club, I get it. Most of these cars are driven on sunny days by older people. When I'm in South Carolina, my C5 is my daily driver except when it rains or I'm on my way to gun range. I'm hard pressed to put more than 3000 or 4000 miles per year on the car.

 Factory Five provides a GTM parts list. They even have a page with pictures of the parts. I make no claims that I know what everything looks like, and they look different sitting in your hand than they do attached to a vehicle.

Fparts uses this same list and provides everything except radiator, alternator, brake pads and brake lines. They print this stuff in red. Parts arrive on a pallet, steel banded and bubbled wrapped or bagged where appropriate. This means items like the steering column are bubble wrapped. Items like the O2 sensors are in bags labeled as such. Items like the fuel tanks, suspension are just sitting there, but these are pretty obvious. The suspension came in four pieces: left, right, front, rear. I don't have to think about putting all those parts together.

So you have the part numbers, description, photos (in some cases) and a list. What could go wrong? I broke things into the following groups:
  • Suspension
  • Fuel Tanks,
  • Steering Column
  • Transmission harness
  • Engine harness
  • Cooling system (e.g. hard pipes, condenser, fans)
  • Doors (e.g. window motors, side view mirrors, handles, seat belts)
  • Small items (e.g. sensors, bolts, tensioner, pulley, ignition)
  • Electronics
I still ended up with a couple of things not on the list, and a couple of mystery pieces. I texted photos to my buddy Brian, who has forgotten more than I'll ever know about cars. He'll either have a good laugh or wish me luck.

I use the same list that Factory Five provides, and Fparts uses to define the donor parts kit. I cataloged everything so I know where I put all these parts. I intend to matched these parts up with the build task list that I developed. I also plan to integrate the Factory Five Parts into the task list. This is my method of knowing where to go find something, when it is time to put it into the build. There are a lot of smart people out there, so you probably have a better way to do this.


Tuesday, July 12, 2011

ISIS Car Wiring System

The project I am currently working on involves updating the front end of the Boxster. One aspect of the new look is the addition of DRLs (daytime running lights) that I purchased from Pedro's Garage. For you Boxster enthusiasts, this is a great site for do it yourself projects.

To get power to the DRLs, I have to tap into the windshield wiper motor. Sounds simple, until you look at all the wires running to and fro just for the wiper motor. Fortunately, I have a multimeter and a very good after market manual. There are several pages devoted to schematics of different electrical systems. As my eyes begin to glaze over, I realize that wiring the GTM could be the hardest part of the build.

So I asked people who have wired cars. My wife's cousin, Tim, has restored several classic cars (and a few other odds and ends) told me to check out American Autowire. If I had a classic Mustang or Corvette that required rewiring, this certainly is the system I would use. However, this is a GTM that I plan to install just about every electronic gadget known to man.

Then I stumbled across the ISIS Multiplex System on the Factory Five Forum. This system might also be referred to as ISquare, 1 + 1 or LittleFuse. ISIS is a modular and scalable electrical system that that manages the lights, signals, dash gauges, electronics, ignition, battery monitoring, electric windows, door poppers (well you get the idea).

Rather than stumble through a poor explanation, I found 4 videos produced by Two Guys Garage. The best part of these videos, they explain the ISIS system and they install it on a GTM!


These videos are about a year old.

Since then, they have added the inMOTION Cell. This module handles item like door poppers, power windows and anything where reverse polarity is necessary to make something run. It manages 5 devices instead of 10 like a regular power cell.

The other addition is the inTOUCH MAX Double DIN Touch Screen. With the exception of turn signals and hazard lights, every switch on the dash can be managed from this touch screen module. Plus you can password protect the car, in addition, the security already built into the master cell. The next video shows an actual install.
I talked to Jay Harris, President of ISIS Power last week. He answered a few more questions:

  • LED lights, flashers - no problem. All of that is managed through the master cell and there is no reliance on electro-mechanical flashers.
  • The different cells are daisy chained via a data cable enclosed in wire loom. On a build like the GTM, there is no order dependence for cells.
  • Back up cameras are not currently supported by the inTOUCH cell. Jay plans to support cameras via inTouch by first Quarter 2012.
  • Custom programming can either be done at the factory, or you can do it yourself.
  • There is lots of info and reference material on the ISIS Power Site.
This is a modular and scalable system that even a computer geek like me can figure out.

Down side: it will cost more, and I will not be using the supplied wiring from the kit.

Up side: the sky is the limit!!

Wednesday, June 22, 2011

The Great Parts Round Up Begins

At my birthday party last night, the guys from my small group asked me what I was up to. I mentioned that I was planning to do a GTM build. It was very reassuring to hear Don give his stamp of approval to Factory Five and the quality of their products. Don is a gear head from way back. Most of the guys were wondering if they could come over and turn some bolts. Certainly! One of the things this kind of project needs is friends.

Don asked if there was much welding. I don't think there is, but he has a spot welder I can use if it comes to that. Again, it is good to know there are friends there to help when (not if) I get into trouble.

I purchased the first real parts for the build: Porsche 930 CV Joints. Porsche OEMs are still making these parts even though they appeared in the 1979 Porsche 911 Turbo (model 930). The Mendeola SDR transmission requires these parts to hook the back wheels into the gear box. These aren't the biggest piece of the car, but it has to start somewhere. Besides the love of my life told me I had to make sure the wheels stayed on the chassis.

Saturday, June 18, 2011

Synergy

I'm zooming down I94 in the Boxster (freshly liberated from storage at the Barn), thinking about integrating GPS into an 11 year old car. I have a very nice Garmin Nuvi on a pedestal mount that I use in the van and the Boxster. Unfortunately the pedestal mount tends to land in the passenger seat on tight turns at speed.

Somewhere north of St. Cloud, it hit me. The Escort SmartMirror is the solution. All I need is power to make the SmartMirror to work, and there is power 2 inches from the mirror mount. The research for my previous post After Market Goodies gave me the answer.
Myrtle Beach Garage
Maple Grove Cave
Another preparatory step is getting the garage ready for the build. The idea of being on the back under a car on a concrete floor in the midst of a Minnesota Winter just doesn't do it for me. I plan to install a non-skid Swisstrax floor. I already know that it works. I have installed this floor in Myrtle Beach garage and the Maple Grove cave. I have had the Corvette on jack stands multiple times. There is no skids, slips. Each tile is rated to 6000 lbs. Neither floor took more than 4 hours to put down.

If you go with a Swisstrax floor, list Traci as your sales agent. She has done super job on my orders!
Search Engine Submission - AddMe